Download Altera University Program Qsim Free

17-08-2021 admin

Introduction to Quartus II Software Design using QSim for Simulation

Quartus II Simulation - Download as PDF File. An introduction to such simulation using Altera’s University Program. To install the Qsim tools, navigate to. Depending on your download speed. The University Program simulation tools, QSim and the Waveform Editor. QSim is part of Altera's University Program. Altera University Program Software. This is a set of Verilog/VHDL files for the DE1/DE2 boards, as well as an easy-to-use C compiler and debugger interface for Nios II. Download the University Program Installer from here. Be sure to select the version that matches your Quartus II distribution.

In this tutorial, we will show you how you capture the schematic design for the automatic door opener circuitusing Altera Quartus II software.

The Problem

We are designing a circuit for an automatic door like those you see at supermarkets. The door should open only when a person is detected walking through or when a person presses a switch (such as the wheelchair button) to have the door open. The door should only operate if it has been unlocked.

output: f = 1 (Opens Door)
inputs
- p = 1 Person Detected
- h = 1 Switch Holding the Door Open
- c = 1 Door Closed/Locked
Want door to open when
- the door is unlocked and person walking through (c=0 and p=1)
- the door is unlocked and the switch is set to hold it open (c=0 and h=1)

Flash drive

While working in the lab, you will want to work from a flash drive or your I: drive account.

You have to be careful if you use the C: drive for your work, for a couple of reasons:

It's easy to lose track of where your files are.
Files on the C: drive are erased when the computer is shut down.

Download altera university program qsim free download

If you do that then you will need to copy your directory to your I: drive or flash driveat the end when you are done.

Each time you create a new project in Quartus II, create a new project directory so that all of the files for each project are in one place and not mixed up with files from other projects.

Getting Started with Altera Quartus

Launch the Altera Quartus software. You should see a screen such as this:

Creating a New project

Always start by creating a new project first, and then create a BDF file. Do not start by creating a BDF file.

Select the File → New Project Wizard; a window like the following will appear.

To select the working directory use the button to browse and select E:CP220intro.
For each project you create in Quartus, create a new folder, and make sure all of the files for that project are in that folder.
Name the project DoorOpener. (Note that the next field gets filled in automatically.)Select Finish.
Don't uses spaces in file or directory names.

Creating a new Schematic design

Select File → New - A window as seen in the following picture will open.

Select 'Block Diagram/Schematic File' and press OK.

This should open a pane where you will design your circuit. This pane is designated Block1.bdf. Save this graphic design file as DoorOpener in your 'intro' directory. The file will be given the bdf extension; bdf stands for block design file and contains schematics, symbols or block diagrams.

Adding text

Select the A below the arrow to the left of your Block Diagram/Schematic File window (also known as the palette).
Select a point near the top left in the window with the left mouse key.
Type your name and then hit the Enter key.
Type your project name and then hit the Enter key.
Type the following equation, f = hc' + pc' , and then hit the Enter key.
Hit the Esc (escape) key to end text additions.

Adding a Component

Click the library icon.The Symbol dialog box will appear. This window lists the available Altera libraries as seenin this image.
Expand the /altera/quartus13.0sp1/quartus/libraries folder, expand the primitives folder and then expand the logic folder.
In the logic folder, select the and2 component by double clicking on it (or by selecting it with a single click, then selecting OK).
Click the pointer at the desired location in the Block Diagram/Schematic Editor window to insert the AND symbol into the design file.

Repeat these steps to enter an OR (or2) gate and a NOT (not) gate.

(If you wanted to add multiple NOT gates, you could select the Repeat-insert mode box.)

In the same manner that you placed a gate onto the palette, add three input pins and one output pin from the Symbol libraries. Input pins can be found under primitives | pin | inputs. Output pins can be found under primitives | pin | outputs.

Name your input and output pins as you name them in your equation. Double click on the pin name to change its name.
Never use spaces in pin names; e.g. 'input 1' is a problem - 'input1' and 'input_1' are ok.

Rearrange your devices in approximately the placement you would like for the logic diagram you are trying to construct. You can move a component by selecting it with your mouse, holding down the left button and moving it to another location on the palette.

Save your design. It is a good idea to save your design often, just in case something bad happens .Save the bdf file with the same name as the project.
Don't use spaces in any file names.

Wiring your circuit

Select the orthogonal node tool. Place your pointer on the output of one of the input pins and hold the left mouse button down. You should see a cross-hairs or + appear at the output.

Drag your pointer to the input of the AND gate. Every time you release the mouse key, the line (wire) ends. If your wire did not reach the AND gate, you can add to the wire by putting your mouse over an end of the wire and again selecting it with your left mouse button and dragging your mouse to another position.
Don't run wires along the edge of a device. This can cause simulation problems.
Don't leave inputs and outputs right next to the chips. Make sure you can actually see some wire between them, otherwise you may have simulation problems.

Note: Make sure you do not make the wire too long. If you drag it too far you will see an x; and this is considered an open connection and your design will not compile.

To delete a wire or a portion of a wire, simply click on it (it should change color to indicate selection) and press the delete key.

If wires are connected to the component as you are moving it, the wires will drag and stay connected to the component. This is referred to as 'rubber banding' and is a feature of all major schematic entry design packages. (You can turn rubberbanding on and off using the rubberbanding tool. )Add the rest of the wires needed to connect the logic diagram.

The window should look something like image below. Save your design.

Printing

We will not print today. But you will need to know how for your project.

To print, go to File | Print. If you want to change what appears on the printout or how it appears, go to File | Page Setup change print settings. Before printing, you can view what the print will look like by selecting File | Print Preview

Choosing a Device

The programmable device which we'll use for our design can be chosen now.

Select Assignments | Device from the pull-down menu.

Select Cyclone II from the 'Family' pull-down list.Any device from the list will do for the simulation.
Choose any device and select 'OK.'

If you get a message like this, don't worry; it's fine.

Circuit Compilation

You will need to compile your design to ensure you do not have any errors in your circuit (e.g. you do not have any open connections, etc.)

Click on Processing | Start Compilation to start compilation.

If you get any error messages, you'll need to fix your circuit before you can simulate it.

Common causes of errors

If you have one of these issues, you need to fix it.

Do you have a project (qpf) open, or just a drawing (bdf)?
Are your project (qpf) and drawing (bdf) files in differentdirectories?
Are there any spaces in your directory or file names?

Circuit Simulation

Note: In version 13.0 of Quartus II, QSim can be opened directly from within Quartus II, however it only works with some Cyclone devices. If you've already chosen a non-Cyclone device, switch to any Cyclone IIdevice to do the simulation. Once you know your logic is correct, you can switch back to your original device.

To open QSim, File | New | New University Waveform File.
Select Edit | Insert | Insert Node or Bus.
Select Node Finder.
Select List.
Select the double right arrow to choose all.
Select OK.
Select OK.
If you have multiple inputs, you can select a bunch and group them with one counter.
Select your input(s), and pick Overwrite Count Value. Select OK.
Select File | Save As to give this file a name in your project directory. It will have a VWF extension for Vector Waveform File.
In the Main window, select Simulation | Options and then select Quartus II Simulator. Select OK.
Note: If you haven't chosen a Cyclone device, the Quartus II Simulator option will be greyed out. In that case, assign the device to any Cyclone II device and recompile.
In the Main window, select Simulation and then select Run Functional Simulation.
( Alternatively, you can use the button on the tool bar.)
Now you should see your simulation output with the outputs defined. Note: The file will indicate 'read-only' meaning you can't edit it.
Note: If you have your inputs in a different order than they are here, then your output will look different becuase the input combinations will be in a different sequence.
You can expand the grouping:
You can navigate around the timeline, zoom in and out, etc.
This part of the output shows that when the inputs are all zero, the output is also zero.

This part of the output shows that when c and h are low, and p is high, the output is high.

This part of the output shows that when c and p are low, and h is high, the output is also high.
You can repeat this process to check all of the eight possible input combinations.
Now if you want, you can go back to the simulation settings and choose Timing instead of Functional to see the effects of propagation delay. In the Main window, select Simulation and then select Run Timing Simulation.
( Alternatively, you can use the button on the tool bar.)